Removing live primers?

Ya let me rephrase that properly - "fkt bro its like the got it in for you" After we knew what to expect, Cody and I had some daring fun from behind a car door size piece of Perspex I have. Yooo! yooo! Daaaad that one would have hit us.
Up side is Cody now has NO, absolutely no misconceptions about ricochets and "ag it will never happen".

This boy of mine has had the fortune to be exposed to a lot of nasty things in a controlled environment. Been bitten by selected snakes, stung by wasps, bees and scorpions. He has seen what electricity is and can do. He has seen how a gas can explode, impressed him that, a balloon full of acetylene dropped from up wind into burning grass.
Invisible danger.
Drug addicts and junkie I know have sat with cody and told him their story, a blind friend, did himself being stupid. Cody has met a friends boy who will never walk again because of a moments "ag it wont happen to me"
Lastly, I organised to visit a hard core mate in max security serving 35 yrs, he and Cody spoke a long time.
I hope it all comes to his betterment

[attach id=1461]Screenshot_20260209_083122_Grok.jpg[/attach][attach id=1463]Screenshot_20260209_082934_Foxit PDF Editor.jpg[/attach]
It is like they were made for each other...

Little glue on the pellet head and you have lively pellets. Like Treeman said, don't shoot at concrete. Wood target is quite exiting.

it also comes back in almost the exact trajectory as it was fired at twice the speed it was fired at. Cody and I shot our front wall and had two come straight back and hit within a few inchs of shooting position and ping pong around inside the garage. We wore goggles "just" in case, and ya, I is one of those things that can go really wrong. We shot the wall at 25 m and it came back like a .22 - honestly, a hard surface and straight shot sends it back A LOT faster than it was sent down - a lot

Maybe I've been very lucky, but I've never had a primer detonate except when hit with a firing pin or airrifle pellet.

A small rifle or pistol primer makes a nice .177 pellet. If it hits something hard, it goes bang on impact.

Maybe I've been very lucky, but I've never had a primer detonate except when hit with a firing pin or airrifle pellet.

I've never set one off either. I susoect that they are impact more than pressure sensitive with a hit being more likely to set them off than a press.

A mate of mine has had multiple primer detonations when loading in his progressive and when trying to help him figure out why his rapid and forceful manipulation seemed the most likely explanation.

Don't leave us hanging on the airrifle pelet thing, what were you up to to get that right?

Maybe I've been very lucky, but I've never had a primer detonate except when hit with a firing pin or airrifle pellet.

You need to deform the primer cup so that the priming compound breaks. This causes the ignition. Pressing on the anvil without undue force doesn't disturb the priming compound.
I've detonated primers on seating, usually when they flip on their side, never on un-seating.

****************************
I have also only ever had a bang with seating primers.

You need to deform the primer cup so that the priming compound breaks. This causes the ignition. Pressing on the anvil without undue force doesn't disturb the priming compound.

I've detonated primers on seating, usually when they flip on their side, never on un-seating.

Just out of interest: how much force, and where, is necessary to detonate a primer?

The primers will come out without incident. Some anvils will separate, most will be fine. You may or may not have a few misfires on those reseated. Not a problem for general range ammo.

Do you want to reuse the primers again or do you plan to toss them away?

Preferably use them again.

I loaded 100+ practice rounds and then learnt that some of the cases are dangerous to use. Now I have to remove the primers to check all the flash holes.

Do you want to reuse the primers again or do you plan to toss them away?

I use a Lee Universal decapping die slowly and gently. I re-use the primers for non-critical tasks like barrel fouling and plinking rounds. Have done it with rifle and pistol primers. I have had a small number of misfires but they were with primers that had been lying around exposed for several years before being re-used.

I'm not recommending this, just sharing what I do.

I've had no issues depriming live primers with a decapping die.

I have experienced misfires after re-seating them, so I don't try re-use them any more.

I have removed many with the decapper pin. Just do it slowly and do wear safety glasses. I have re-used those primers without any issues.